Jump to content

Close
--Click to Remove Ads--
Photo
- - - - -

Measurements of Pickle Fork Shooter


  • Please log in to reply
13 replies to this topic

#1 dgui

dgui

    Resigned

  • Resigned
  • 5,563 posts
  • Locationusa

Posted 15 April 2011 - 03:49 PM


http://i1127.photobu...urements001.jpg

#2 forest dude

forest dude

    100 Post Club

  • Bronze Sponsor Bronze Sponsor
  • 123 posts
  • LocationEarth, probably.

Posted 18 April 2011 - 05:13 PM

Thanks for posting this! As soon as I have time I will turn one of these out. I want to play around with your "rifle" gip.

best,
Steve

#3 dgui

dgui

    Resigned

  • Resigned
  • 5,563 posts
  • Locationusa

Posted 18 April 2011 - 06:54 PM

Thanks for posting this! As soon as I have time I will turn one of these out. I want to play around with your "rifle" gip.

best,
Steve


Hey ForestDude,

Actually Philly took my posted picture of the measurements I did and he did it over and very professionally and he even put in the radius part on the handle so if he is reading this perhaps he can post the one he did it is so much better than mine. My attempt at copy and paste here did not work. Also I have a plan to make a shooter like this but with a rifle type shooter but the timing just does not seem to be working out yet.


#4 dgui

dgui

    Resigned

  • Resigned
  • 5,563 posts
  • Locationusa

Posted 18 April 2011 - 07:12 PM

Hey ForestDude, My mistake, Philly had already posted it in the Design section of the forum but here it is. http://www.4shared.c...LINGSHOT_2.html








#5 Bill Hays

Bill Hays

    2000 Post Club

  • Vendors Supporting Vendor
  • 2,716 posts
  • LocationTexas

Posted 18 April 2011 - 10:15 PM

Tell you what Darrell, I'll make two of these out of black 1/4" thick G10, PM me your address and I'll send you one.

#6 philly

philly

    Philly

  • Bronze Sponsor Bronze Sponsor
  • 2,595 posts
  • LocationNorth East

Posted 19 April 2011 - 07:51 AM

Darrell, Chuck, MXRED posted the PDF on the shared forum thread, I worked from your drawing. Which was fine for me.
Philly

#7 dgui

dgui

    Resigned

  • Resigned
  • 5,563 posts
  • Locationusa

Posted 20 April 2011 - 09:03 AM

Darrell, Chuck, MXRED posted the PDF on the shared forum thread, I worked from your drawing. Which was fine for me.
Philly



Oh, my mistake, Thanks.

#8 dgui

dgui

    Resigned

  • Resigned
  • 5,563 posts
  • Locationusa

Posted 20 April 2011 - 09:04 AM

Hey Mix,

Thanks for Posting the Drawing.


#9 dgui

dgui

    Resigned

  • Resigned
  • 5,563 posts
  • Locationusa

Posted 20 April 2011 - 09:05 AM

Tell you what Darrell, I'll make two of these out of black 1/4" thick G10, PM me your address and I'll send you one.


Hey Bill, That would be Awesome, I will do that.


#10 Frodo

Frodo

    500 Post Club

  • Registered
  • 740 posts
  • LocationHamburg- Germany

Posted 12 May 2011 - 03:31 PM

Just saved the drawing. I will try that mighty PFS..

#11 dgui

dgui

    Resigned

  • Resigned
  • 5,563 posts
  • Locationusa

Posted 12 May 2011 - 04:06 PM

Just saved the drawing. I will try that mighty PFS..


Great, be sure to turn the pouch so it is sideways and not up and down and tilt the shooter farward a few degrees and you will have it.

#12 Gwilym

Gwilym

    250 Post Club

  • Bronze Sponsor Bronze Sponsor
  • 416 posts
  • LocationWales

Posted 12 May 2011 - 04:12 PM

I don't understand what you mean dgui by not up or down

#13 mckee

mckee

    2000 Post Club

  • Registered
  • 2,938 posts
  • Locationbritain

Posted 12 May 2011 - 04:16 PM

I don't understand what you mean dgui by not up or down


he means tilt the pouch to the side to avoid fork hits :)

#14 dgui

dgui

    Resigned

  • Resigned
  • 5,563 posts
  • Locationusa

Posted 12 May 2011 - 04:30 PM

I don't understand what you mean dgui by not up or down


It's just like McKee said and the only thing I will add to that is this video and if you do this it works.








--Click to Remove Ads--